Your home's exterior takes a beating every single day — sun, wind, rain, impact. When siding fails, moisture gets in fast and damage follows. Forge Siding sends licensed Siding crews across Waverly, NY to inspect, repair, and replace with zero guesswork.
Forge Siding grew out of a simple frustration: too many Waverly homeowners were paying good money for Siding work that failed inside five years. Wrong profiles, wrong fastener gauges, no housewrap — then the callbacks never came. We do it right the first time, using manufacturer-recommended installation methods and materials rated for NY's specific climate demands.
Every estimate is itemized and written down before we ever ask for a signature. You'll see material costs, labor, disposal, and any underlying repair work broken out separately — so you know exactly what you're paying for and why. We've completed thousands of Siding projects across Waverly, NY and our callback rate is under two percent. That number matters to us.
Most homeowners don't notice siding problems until water damage has already reached the sheathing. These are the signals worth acting on before the repair scope doubles.
Hairline cracks look cosmetic but they're water channels. Once moisture gets behind the panel and hits the housewrap — or finds no housewrap at all — sheathing rot starts within one season.
Panels that bow outward have usually absorbed moisture or were installed without adequate expansion clearance. Warped vinyl or fiber cement can't seal properly at the joints, so the problem accelerates.
Paint peeling on your inside walls near exterior surfaces is a classic sign that moisture is migrating inward through failing siding. By the time you see it inside, the wall cavity is already compromised.
Panels that have pulled away from the wall are an open door for pests, moisture, and cold air. Nails back out over time when the substrate is soft — often a sign of prior water damage underneath.
Old or failing siding, particularly if the housewrap underneath has deteriorated, acts like a thermal short-circuit. Your HVAC runs harder to compensate, and the bills reflect it before the siding looks obviously bad.
Extreme fading means UV degradation — the protective surface layer is gone. Chalking on older paint-based systems signals the same. At that stage, the panel is no longer blocking UV penetration to the substrate underneath.
From a single damaged panel to a complete re-side on a large commercial property, we handle the full range of exterior cladding work — and we do it with the same crew standards regardless of job size.
Fiber cement comes in lap, panel, and shingle profiles, and we've installed all three on everything from Cape Cods in historic neighborhoods to large multi-unit builds. Correct installation matters enormously with this material — improper fastening or insufficient clearances void the warranty and cause edge-swell failures. Our lead installers are trained to the spec sheet, not just to what looks right on the jobsite.
Done right, vinyl siding is durable, low-maintenance, and cost-effective. Done wrong — wrong gauge, wrong fastener pattern, no expansion clearance — it warps in the heat and pulls loose in wind. We use .044" and .046" gauge panels minimum and follow thermal expansion specs precisely for NY's temperature range. Nail hem fastening at 16" centers, 1/32" expansion gap at all trim terminations, and a fully integrated vinyl accessory system so the corners, J-channel, and window trim all work together.
Engineered wood is popular in Waverly neighborhoods where the traditional wood look matters architecturally but the maintenance demands of real cedar or pine aren't practical. We install with stainless or hot-dipped galvanized fasteners to prevent iron staining at the nail head — a detail that separates a professional installation from a quick flip job.
Not every siding problem needs a full re-side. Storm impact, vandalism, or isolated rot can often be addressed with a targeted repair that blends into the existing field. We stock common profiles and can often source discontinued patterns through our supplier network for historic or older homes where matching matters. Partial replacement work is priced honestly — if we see a repair scope that's going to creep, we say so before we start, not after.
We work with metal panel systems, large-format fiber cement, and commercial-grade vinyl for multi-family and light commercial applications. EIFS compatibility work, expansion joint detailing, and coordination with waterproofing and window subcontractors are all in scope. We carry the insurance requirements for commercial GC work and can provide certified payroll documentation for public projects.
Siding that terminates at rotted or missing fascia boards isn't protected — it's channeling water straight into the rafter tails. We routinely pair siding replacement with trim, soffit, and fascia work so the entire exterior envelope is addressed in one mobilization rather than two. PVC trim board, prefinished aluminum coil, and fiber cement fascia are all in our wheelhouse.
We built our process around the two complaints we heard from homeowners most: contractors who didn't communicate, and scopes that changed after signing. Here's exactly how a Forge Siding project runs from start to finish.
A thorough inspection before we quote means the estimate we hand you is accurate. We check the substrate, the existing housewrap or vapor barrier, window and door flashing, corner and soffit condition — all of it — so there are no hidden surprises once demo starts.
You receive a line-by-line written estimate: material cost by product and quantity, labor, removal and disposal of existing siding, and any sheathing repair identified in the assessment. We walk through material options with physical samples, not just catalog photos. You sign off on the spec before we order anything.
Your start date is locked at signing. Crew arrives on time, materials are staged and ready, and the site is protected before demo begins. We run a tight job — no leaving panels exposed overnight when rain is in the forecast.
At project completion, we walk the entire exterior with you. Every run of siding, every corner, every trim termination — you look at it before we close out. If anything isn't right, it gets fixed on the spot. Our goal is that you refer us to your neighbor the week after the project wraps.
We don't sub out work to unlicensed handymen to cut costs. Every installer on a Forge Siding project is a W-2 employee or licensed sub with verified credentials and completed manufacturer training.
Upfront pricing means you know what you're paying before a single panel comes off the wall. Change orders require your written approval. We've built our reputation in Waverly, NY on the fact that our estimates are reliable.
When we book your project, we commit to a start date. No bumping you for a bigger job, no weeks of silence after signing. We operate with enough crew capacity to honor the schedule we gave you.
We've seen what happens when crews leave siding debris sitting for a week. Nails in the lawn, panels blocking access, dust in the HVAC intake. Our cleanup protocol runs end-of-day, not end-of-project.
Every Siding project we complete is backed by our written workmanship warranty. If anything we installed fails due to installation error — a panel pulls loose, a trim joint opens, moisture gets in at a transition we sealed — we come back at no charge and fix it. Not a credit, not a partial. Fixed.
Get the Details on Our Warranty — +1-844-782-0929We don't cherry-pick — these are verbatim accounts from homeowners who hired us for Siding work across Waverly, NY.
We were replacing deteriorated T1-11 on a house we'd bought the year before. Forge Siding walked us through why HardiePlank made more sense than vinyl for our wall orientation and explained the flashing work that needed to happen around the windows before panels went on. Project started on the date they said. Crew cleaned up every afternoon. The job came in within a couple hundred dollars of the estimate.
A storm took out a whole section of vinyl on the east side of our house. I called four contractors — three of them said they'd have to replace the entire elevation because they couldn't match the profile. Forge Siding's estimator sourced a matching panel through their supplier network and did a clean repair. You can't tell where the new material starts. Saved us probably $4,000 compared to a full-side re-do.
We went with insulated vinyl — Forge Siding recommended the insulated backer for our exposure and the energy savings have been real. First heating season after the install, our gas bill dropped noticeably. Installation crew was professional, on time every day, and the lead installer walked me through every elevation before he called the project done.
I had a specific architectural profile I wanted for the gable ends — a shingle exposure pattern — and everyone else told me it was a custom order with a six-week wait. Forge Siding had it in stock through their regional supplier and we started within two weeks of signing. The detail work at the gable peaks is clean and exact. Not every contractor has the skill to do that level of trim work.
I'm a home inspector by trade, so I know what cutting corners on a siding installation actually looks like behind the panels. Forge Siding's work is correct — right fastener pattern, proper clearances from grade and roofline, continuous housewrap with taped seams at all penetrations. This is how it's supposed to be done and most of the crews I see in Waverly, NY don't do it this way.
We had three bids and Forge Siding was the only contractor who physically checked the housewrap condition before quoting. Everyone else just looked at the surface. They found a section of torn WRB behind the garage bay that needed patching and included it in the estimate. When you're spending this much on an exterior, you want a company that checks the whole wall system, not just what they can see from the ground.
We get these questions every week. Here are the honest answers.
We're not a national call center subcontracting your project to whoever's available. Our crews are based in and around Waverly, NY. We know local code requirements, local supplier lead times, and local weather patterns — and that local knowledge shows up in how the project runs.
Reach us at +1-844-782-0929 and we'll confirm service at your location. Most addresses in and around Waverly are within our standard service radius with no travel fee.
Free written estimate. Licensed crew. Scheduled start date. Call Forge Siding now and get a real assessment — not a ballpark number over the phone.
Schedule My Assessment — +1-844-782-0929